Electronics Design Engineer x 4

£81.90 per hour (inside IR35)

Portsmouth

Monday to Thursday onsite

Defence

This is a technical role relating to the Electronic aspects of hardware design & test.

The Role Holder will :-

Develop and/or support electronic design solutions for both new products and technology insertions into legacy products.
Produce and/or support detailed designs from concept to completion and addressing a range of engineering challenges.Participating in all aspects of board‑ and unit‑level design and test activities, including interfaces with higher‑level assemblies.

Typical duties include (but are not limited to):

§ Detailed electronic circuit design including component selection, evaluation, simulation, schematic capture, and liaising with PCB design teams.

§ Specification of bespoke procured hardware.

§ Design verification using a combination of simulation, analysis, and test techniques, including support to EMC test houses and customer installations.

§ Generate design documentation and technical reports.

§ Interfacing with related disciplines.

§ Assist the development of higher level system designs.

§ Assist the development of technical requirement specifications

§ Support system integration activities.

§ Work with embedded software and PLD engineers as necessary

§ Contribute to progress, peer, and design reviews.

Knowledge:

§ Generating component level electronic designs for introduction into volume production.

§ Digital design including processor interfacing, memory devices, PLD interfacing, UARTs, SPI, I2C, Ethernet etc.

§ ADC/DAC devices and techniques

§ Analogue design including op-amps, transistor-level design, control loops and low noise techniques.

§ High power techniques.

§ Design proving, integration, and defect resolution.

§ Gathering of evidence to support acceptance, fitness for purpose, legislative requirements, and safety.

Skills:

§ Previous experience of operating in a defence or high safety integrity environment.

§ Experience of low-noise analogue techniques

§ Experience of high power techniques (kW level)

Experience of FPGA/CPLD development

Industrial Engineering / Petrochemical / Oil and Gas

Location | Working Pattern | Salary
Chichester, West Sussex | Primarily site-based (flexibility available) | £50,000-£70,000 + car/allowance + great benefits

About the Company

A specialist engineering organisation supporting major industrial and energy-sector clients across the UK and internationally. The business designs and delivers complex engineered systems used in hazardous environments and is undergoing a period of growth and transformation, strengthening its leadership structure to support future projects and long-term capability.

Why This Role?

* Opportunity to shape and lead the future of an electrical engineering function during a key transition

* High level of ownership and visibility within a collaborative engineering environment

* Chance to influence processes, team development, and technical standards

* Work closely with senior stakeholders across engineering, projects, and commercial teams

* Strong relationships with customers by building long-term relationships through proactive engagement

The Role – What You’ll Be Doing

* Lead and support a EC&I team covering electrical design, instrumentation, and commissioning activities

* Take ownership of electrical aspects across projects from concept through to FAT and delivery

* Review and approve technical documentation including drawings, specifications, and design outputs

* Support project delivery by working closely with mechanical, commercial, and project teams

* Specify and select electrical and instrumentation components for complex industrial systems

* Contribute to process improvements and help build structure within the engineering function

* Provide technical input into tenders and customer-facing activities

This is a hands-on leadership role where you’ll oversee technical delivery while helping shape the direction of the department as it evolves.

The Person – What We’re Looking For

* Strong EC&I background within heavy industry, petrochemical, oil & gas, or similar environments

* Experience in electrical design, instrumentation, and control systems (PLC/SCADA awareness beneficial)

* Knowledge of hazardous area environments (ATEX/COMPEX exposure highly desirable)

* Able to lead, mentor, and support a small technical team

* Comfortable collaborating across departments and engaging with customers

* Practical, solutions-focused mindset with the confidence to challenge and be challenged

* HNC (or equivalent) in Electrical Engineering, or substantial relevant industry experience

* Able to travel to customers’ sites as and when required

What You’ll Get

* Corporate benefits

* Car allowance or company car

* Pension and additional company benefits

* Flexible start/finish times and some working flexibility

* Opportunity to play a key role in a growing engineering team

To apply for this career-defining role please do forward your CV

Well established South Coast based Fast Fit Out Contractor currently seek an Electrical Project Manager to be the Project Lead on various fast-paced commercial office fit-out projects. You must be able to clearly demonstrate the ability to manage the full project lifecycle of multiple Cat A and Cat B fit-outs whilst being the “go-to technical expert” of the Electrical Division of the business. You will also be responsible for delivering projects on time, within budget and in full compliance with Health & Safety.
Electrical Project Manager Qualifications & Experience
* SMSTS and Black CSCS Card
* Minimum of 5 years experience in Project Management within the Commercial Fit Out Sector
* Trade Qualifications such as (NVQ Level 3 or equivalent) with a Gold JIB Card and 18th/19th Edition updates
Electrical Project Manager Key responsibilities
* End-to-End Project Delivery of CAT A and B projects from pre-construction through to handover and aftercare.
* Programme Management through developing and maintaining detailed project schedules ensuring critical milestones are met across all live projects
* Financial Control through budget and procurement management, tracking of variations and final accounts to ensure maximum profitability without compromising quality.
* Stakeholder Liaison by acting as the primary point of contact for clients, architects, and consultants, translating complex technical requirements into clear project updates.
* Ensuring Compliance within the Electrical Division
* Technical Authority acting as the “Electrical Lead” for the company ensuring all electrical installations across all company projects meet current BS 7671 (IET Wiring Regulations) standards.
* Compliance Auditing to ensure the Electrical Division is adhering to statutory regulations.
* Certification Management ensuring the timely production and filing of all electrical testing, commissioning data, and O&M requirements.
* Pre-Construction Support working closely with the commercial team to ensure that electrical tenders are vetted appropriately to ensure value engineering, and design feasibility.
* Cross Project Resolution Serve as the “on-call” technical expert for complex electrical challenges across all projects
* Sub Contractor Management review and manage electrical subcontractors to ensure that high standards of workmanship and reliability are maintained
Electrical Project Manager Salary & Benefits
* Base Salary of Circa £70k (Negotiable)
* Car Allowance
* 30 days Annual Leave (inclusive of Bank Holidays)
* Pension Scheme.
Primary Location is Southampton but the Projects are based (although not limited to) London and the South Coast. Ideal location would be 35 to 45 minute commute to the office.
Cleveland Eton are acting as a Recruitment Business in relation to this vacancy. By applying you are granting us consent to contact you in relation to this application. Your details will remain confidential and will not be provided to any other party without your express permission. We look forward to hearing from you

£60,000 Basic Salary + Company Benefits + Overtime

Monday - Friday - Day Shift

Our client, a market-leading manufacturing business, is currently seeking experienced Multi Skilled Engineers to join their established engineering and technical team. This is an excellent opportunity to work within a modern, highly automated factory environment for a forward-thinking organisation that invests in both its people and its technology.

Key Responsibilities:

* Carrying out planned and reactive electrical & mechanical maintenance across all production and site operations

* Diagnosing faults and maintaining a wide range of automated machinery, including: Robotics, Conveyor systems,PLC-controlled equipment, Mechanical, electrical, hydraulic, and pneumatic systems

* Ensuring all machinery is maintained to a high standard, minimising downtime and maximising productivity

* Supporting production teams with machine breakdowns, changeovers, and set-ups

* Identifying opportunities for continuous improvement

* Assisting with the installation, commissioning, and modification of equipment

* Providing technical guidance and training to operators where required

* Ensuring all work is carried out in line with company procedures, health & safety regulations, and industry standards

If you are interested in this Multi Skilled Engineer role, please submit an up-to-date CV through this advert

Senior Mechanical Engineer – Building Services Design
MOD, Education, Residential, Retail & Healthcare projects
Portsmouth / Waterloo Area
Salary up to & around £60,000 + benefits + bonus

We’re looking for a Senior Mechanical Engineer with proven Building Services Design experience to join a growing team near Portsmouth!!!

Ambitious individuals, close knit, dynamic team, high growth, stable & profitable projects, growth to management level, multi-discipline teams and the chance to work on the newest renewable technologies within the Built Environment!

If you have Mechanical Engineering experience within the Built Environment and now looking for your next position, this is the role for you!

About the company & position?
This young and growing team are an outgoing and passionate group of individuals, with a high percentage of their work in the MOD sector, alongside education, healthcare, residential and retail projects. You will be required to go through security clearance in time for the MOD side of their work, which will give you access to a huge range of different buildings to work on and types of engineering within the sector.

Due to a mass update of MOD buildings, this business is the chosen consultancy, so you will get the opportunity to work with a huge range of Renewables Emerging Technologies, such as Hydrogen Systems, Air Source, Heat source pumps, upgrading Electrical PV systems and much more! If you want to be at the forefront of these technologies, be in a position with solid stability and growth potential, this is the role for you!

This practice is family run and has 25 people working for them. As an inclusive company with low staff turnover, you will be working in the projects team (made up of 15 engineers and building surveyors) who provide businesses with net zero carbon targets. The overall team of 25 individuals are extremely settled, offering Architectural, Sustainability and Surveying services across the south of England, with more services being slowly added.

This company offer flexibility and hybrid working, with this individual being expected to be in the office more often that not to start off with. The company offers a full range of professional property services across Southern England including surveying, mechanical and electrical engineering, and architecture.

What can they offer the successful Senior Mechanical Engineer?

A young and dynamic group of individuals.
Using AutoCAD and Revit.
A growing business hoping to double in size over the next 2 years.
Progression and support with career development.
The chance to work on a huge range of projects.
Renewable emerging technologies exposure, rather than the usual HVAC systems.
Flexible hybrid working for more experienced individuals.
Yearly company and individual performance bonus, alongside competitive salary. For more information on this role, contact Jevon Astley-Jones for more information and a faster application

Electrical Engineer – Building Services Design
MOD, Education, Residential, Retail & Healthcare projects
Portsmouth / Waterloo Area
Salary up to & around £50,000 + benefits + bonus

We’re looking for an Electrical Engineer with proven Building Services Design experience to join a growing team near Portsmouth!!!

Ambitious individuals, close knit, dynamic team, high growth, stable & profitable projects, growth to management level, multi-discipline teams and the chance to work on the newest renewable technologies within the Built Environment!

If you have Electrical Engineering experience and now looking for your next position, this is the role for you!

About the company & position?
This young and growing team are an outgoing and passionate group of individuals, with a high percentage of their work in the MOD sector, alongside education, healthcare, residential and retail projects. You will be required to go through security clearance in time for the MOD side of their work, which will give you access to a huge range of different buildings to work on and types of engineering within the sector.

Due to a mass update of MOD buildings, this consultancy is the chosen consultancy, so you will get the opportunity to work with a huge range of Renewables Emerging Technologies, such as Hydrogen Systems, Air Source, Heat source pumps, upgrading Electrical PV systems and much more! If you want to be at the forefront of these technologies, this is the role for you!

This practice is family run and has 25 people working for them. As an inclusive company with low staff turnover, you will be working in the projects team (made up of 15 engineers and building surveyors) who provide businesses with net zero carbon targets. The overall team of 25 individuals are extremely settled, offering Architectural, Sustainability and Surveying services across the south of England.

This company offer flexibility and hybrid working, with this individual being expected to be in the office more often that not to start off with. The company offers a full range of professional property services across Southern England including surveying, mechanical and electrical engineering, and architecture.

What can they offer the successful Electrical Engineer?

A young and dynamic group of individuals.
A growing business hoping to double in size over the next 2 years.
Progression and support with career development.
The chance to work on a huge range of projects.
Renewable emerging technologies exposure, rather than the usual HVAC systems.
Flexible hybrid working for more experienced individuals.
Yearly company and individual performance bonus, alongside competitive salary. For more information on this role, contact Jevon Astley-Jones for more information and a faster application

Fire & Security Engineer - Southampton
Salary: £38,000 - £45,000 (DOE) | Service & Installation

An established and reputable fire and security company is seeking an experienced Fire & Security Engineer to join their team covering Southampton and surrounding areas. The business delivers a wide range of projects across commercial and residential environments and is known for maintaining high technical standards while providing a supportive working environment for its engineers.

This position involves both service and installation work across a variety of fire and security systems. The successful candidate will be responsible for installing new systems, carrying out planned maintenance, diagnosing faults, and ensuring all systems operate in accordance with current industry standards and client specifications.

Key Responsibilities

* Installation of fire alarm, CCTV, intruder alarm, and access control systems across a range of sites
* Servicing, maintaining, and fault finding on existing fire and security systems
* Ensuring all work is completed in line with industry regulations and company procedures
* Completing job documentation and maintaining high standards of workmanship
* Working independently or as part of a wider engineering team to deliver projects effectively

Candidate Requirements

* Proven experience working with fire and security systems in a service and/or installation capacity
* Good technical knowledge of fire alarms, CCTV, access control, and intruder alarm systems
* Strong fault finding ability and attention to detail
* Professional approach with good communication skills
* Ability to manage workload and work independently when required

What’s on Offer

* Basic salary between £38,000 - £45,000 depending on experience
* A varied role covering both installation and service work
* Ongoing training and development opportunities
* Stable and well-established company with a strong pipeline of projects
* Supportive management and a professional working environment

This opportunity would suit an experienced Fire & Security Engineer seeking a long-term role within a well-organised company delivering a consistent range of projects across the Southampton area.

Relevant backgrounds may include:
Fire & Security Engineer, Fire Alarm Engineer, Security Engineer, Fire Alarm Service Engineer, Fire Alarm Technician, Intruder Alarm Engineer, CCTV Engineer, Access Control Engineer, Service Engineer, Electrical Engineer, Electrician, or Maintenance Electrician.

INDAV

HVAC Service Engineer

Location: Portsmouth (field-based across Portsmouth & surrounding areas)
Salary: £42,000 - £52,000 DOE
Benefits: Company van, fuel card, overtime, call-out allowance, pension, 25 days holiday plus bank holidays
Contract: Permanent, Full-Time

A leading building services and facilities management contractor is seeking an experienced HVAC Service Engineer to support a portfolio of commercial and industrial clients across Portsmouth and the surrounding areas.

This is a stable, long-term opportunity offering structured training, manufacturer support, and clear progression for engineers looking to develop both technically and professionally.

Role Responsibilities

Planned preventative maintenance (PPM) and reactive repair works on HVAC systems

Fault diagnosis on electrical, mechanical, and refrigeration components

Servicing and maintenance of:

Split & multi-split air conditioning systems

VRV / VRF systems

AHUs, FCUs, and ventilation systems

Heat pumps and chillers (experience-dependent)

Carrying out pressure testing, leak detection, evacuation, and re-gassing

Completing service reports, F-Gas logs, and compliance documentation

Liaising with clients, site contacts, and helpdesk teams

Ensuring all works are carried out in line with:

F-Gas regulations

Health & Safety legislation

Company and site procedures

Participation in an on-call rota (typically 1 in 6 / 1 in 8)

Essential:

Minimum 3+ years’ experience as an HVAC / AC Service Engineer

F-Gas Category 1

Strong fault-finding capability on HVAC systems

Good working knowledge of electrical and mechanical components

Full UK driving licence

Comfortable working independently in a field-based role

Desirable:

NVQ Level 2/3 or City & Guilds in Refrigeration & Air Conditioning

Experience with chillers, heat pumps, or commercial ventilation

18th Edition (BS7671)

IPAF / PASMA

Interested?

INDAV

If you believe you have the skills and experience to excel in this role, apply today.

Alecto Recruitment Limited is acting as an employment business for this vacancy. We thank all applicants for their interest; however, only those shortlisted will be contacted.

Keywords:
HVAC Engineer Portsmouth, Air Conditioning Engineer Portsmouth, HVAC Service Engineer Portsmouth, AC Engineer Portsmouth, Refrigeration Engineer Portsmouth, Commercial HVAC Engineer, VRV Engineer Portsmouth, VRF Engineer Portsmouth, Facilities Management HVAC

Info about the company

We are working with a well-established product manufacturer based in Havant that designs and builds high reliability equipment used in safety critical environments. Engineering is central to the business, with mechanical, electronics and embedded teams working closely together across the full product lifecycle, from concept through to manufacture.

*There is no visa sponsorship available for this role, and a UK driving license is required*

Benefits

* 9 day fortnight (every other Friday off)

* Up to 10.5% employer contributions

* Share scheme

* Bonus scheme

* Healthcare

* Hybrid working

Info about what the Mechanical Design Engineer role entails

This Mechanical Design Engineer role centres around designing plastic injection moulded components for high volume manufacture. You’ll be responsible for delivering practical, manufacturable designs and supporting products through development and into production.

Essential Requirements of a Mechanical Design Engineer

* Experience designing injection moulded plastic parts

* Background in high volume manufacturing

* Strong understanding of design for manufacture

* 3D CAD experience

Desirable Requirements of a Mechanical Design Engineer

* Experience working on safety critical or regulated products

* Exposure to automated manufacturing environments

* Experience supporting products through testing and into production

If you feel you are suitable and interested in this role, APPLY NOW with an up-to-date CV. We also pay referral fees if you can suggest another suitable person that isn’t already known to us.

April Quest Ltd acts as both an Employment Business and Employment Agency and complies with the Conduct of Employment Agencies and Employment Businesses Regulations Act 2003. We take your privacy seriously; our Privacy Policy can be viewed on our website

Maintenance Engineer - Day Shift (Portsmouth)

A fantastic opportunity has arisen for a Maintenance Engineer to join a growing precision engineering environment on a day-shift, full-time basis (40 hours, Monday-Friday).
This is a brand-new role, offering the successful candidate the chance to shape the position, establish processes, and implement effective structures from the ground up. It’s ideal for someone confident working independently and keen to make a meaningful impact.

Key Responsibilities:

• Conduct both mechanical and electrical maintenance across a variety of engineering equipment.
• Support and improve the maintenance function through proactive problem-solving.
• Develop and implement structured processes, maintenance routines, and continuous improvement initiatives.
• Fault-find on machinery with a particular emphasis on CNC equipment, including 5-axis systems.
• Work autonomously while also supporting production teams when required.

Key Requirements

• Strong background in maintenance engineering, covering both mechanical and electrical aspects.
• Experience within a precision or CNC-driven environment is highly desirable.
• Demonstrated stability and commitment in previous roles.
• Ability to take initiative and introduce effective processes in a new, evolving position.
• A proactive, solution-focused mindset with strong organisational skills.

About the Environment
You’ll be joining a leading precision engineering setting known for its expertise in 5-axis CNC machining, toolmaking, and rubber moulding. Operating to ISO 9001:2015 standards, the environment supports sectors including automotive, aviation, and defence - offering variety, challenge, and high-level engineering exposure.

If you’d be interested in finding out more please apply or contact Max Fairclough at Shorterm Group

New opportunity to join one of the UK’s leading independent bulk liquid storage providers, operating four strategically located terminals across the country. The Company supports a wide range of sectors including chemicals, petroleum, gases, bitumen, and emerging energy markets such as hydrogen, sustainable aviation fuel (SAF) and carbon capture.

As a key part of the UK’s critical national infrastructure, Navigator is committed to safe operations, exceptional customer service, and ongoing investment to support future growth and the energy transition.

A vacancy now exists for an Electrical Engineering to join the team.

Negotiable Salary + Bonus + Private Healthcare

The role

You will be a Subject Matter Expert for electrical systems and equipment, ensuring safe and reliable operation of our client’s electrical systems and electrical assets.

Provide technical support, leadership and guidance to projects, operations, and maintenance.

Take responsibility for electrical aspects of projects & modifications, developing and reviewing designs and specifications for new electrical systems and equipment.

Key Accountabilities:

Responsible for implementation of the companies Electrical Safety Rules and review as required in line with changes in legislation and industry best practise.
Designated Electrical Competent Person under Electricity at Work Regulations for all Navigator terminals. Authorising Engineer.
Competency assessment of site electricians and contractors’ electricians.
Specification, budgeting and scheduling of electrical inspection and preventative maintenance, including HV / LV and ATEX routines to ensure reliable, safe and reliable operation.
Development of HV switching programs
Responsible for the application of appropriate electrical engineering codes and standards and management of any deviations from standards.
Technical review of designs undertaken by Navigator engineers and design houses.
Prepare cost estimates and business case proposals for electrical equipment/system CAPEX.
Responsible for OPEX and CAPEX budgetsSite Electrical Equipment includes:
Power Transformers, HV/LV Switchgear Air, Vacuum and Oil, HV/LV distribution, tripping batteries, transformer rectifier units, ATEX and FLP Motors, Motor Starters, HV / LV VSDs, Soft Starts, UPSs, lighting, trace heating, industrial immersion heaters, HVAC, Hazardous Area Cabling/Containment/Junction Boxes, Lightning Protection Systems and Earthing and Bonding Systems.

Required Skills, Qualifications & Experience:

Degree educated in Electrical Engineering
Chartered Engineer Status or working towards Chartership
Experience managing design/installation/commissioning and maintenance of electrical systems on a COMAH site, preferably in the bulk liquid storage sector
Significant electrical system design experience, load lists, SLDs, cable sizing, fault level, protection grading studies and motor starting calculations. Lightning protection calculations.
Specification of equipment for installation in Hazardous areas
Risk Assessment
Site Commissioning and Troubleshooting experience
Experience as designated competent person under Electricity at Work Regulations. Experience in roles such as: Authorised Person, Senior Authorised Person, Control Engineer and Authorising Engineer
Experience in managing ageing assets
Experience in training and mentoring site electricians
CompEx Ex01 - 04
CompEx Design (Ex12), parts A & B
Working Knowledge of applicable codes and standards such as BS 7671 and BS EN 60079.Knowledge and skills will cover hydrocarbon & chemical storage, process safety and knowledge of UK specific regulations such as Electricity at Work Regulations, DSEAR, PUWER, CDM and COMAH

Job Title: Asda Refrigeration Engineer

Location: Walsall/ Wolverhampton

Contract Type: Permanent

Working Hours: 45 hours per week

Salary: £(phone number removed) Total Salary (Inclusive of Standby Payment), Overtime, Travel Time, 33 Days Holiday, Private Pension & Benefits - Including Private Health Care, Life Insurance, Employee Discounts

This is a key position, carrying out planned and reactive maintenance across several Asda site locations.

You will be the first line in all service and maintenance throughout your allocated sites.

To effectively maintain service and repair Refrigeration Equipment in customer locations and provide assistance to HVAC equipment containing refrigeration circuits.

Engineering teams provide 24hr service cover throughout the year to customer’s equipment through the use of planned and extended working hours including participation in standby rota procedures.

Key Accountabilities:

* Prioritise maintenance and repair work to achieve agreed timescales and response times.

* Identify non-repairable faults promptly advise the Line manager of findings, with recommendations regarding suitable replacements.

* To ensure PPM schedules are completed within agreed timescales and that all necessary paperwork is completed accurately and to the laid-down procedures.

* Ensure that all technical and compliance paperwork is always completed and up to date.

* Requirement to participate on an out of hours standby rota. Responsible for arranging & communication of any cover required due to holidays/ unforeseen circumstances to line manager.

Knowledge, Skills and Abilities:

Essential:

* NVQ/C&G Refrigeration Based Qualification

* Refrigerant Handling C&G 2079 or equivalent CITB certificate

* Refrigeration, Electrical, Air Conditioning & Mechanical knowledge

Desirable:

* BS7671 (IEE 16/17th)

* Commercial/Supermarket

* Machine Overhaul Skills

* Hydrocarbon Refrigerant Training

* CO2 Refrigerant Training

The ideal candidate:

* Good communication skills (written and verbal)

* 5+ years’ experience

* Full driving licence

Senior Engineer (Electrical Safety), On-Site / Fareham Area

Join a leading global technology and safety consultancy and play a key role in helping manufacturers bring compliant, safe electrical products to market. We are seeking an experienced Senior Engineer (Electrical Safety) to support testing, certification, and compliance activities for a wide range of electrical devices.

This is an on-site role based in the Fareham area, offering the opportunity to work closely with clients while developing expertise in global product safety and certification.

Why this role?

On-site position based in the Fareham area
Work with global clients on electrical safety and compliance projects
Opportunity to develop as a Product Safety Specialist within an international organisation
Exposure to global market access and certification processes

What you’ll do:

Carry out electrical safety testing and design assessments at laboratory and client sites
Identify compliance requirements and develop practical strategies to achieve certification
Support CE marking and global market access for electrical products
Conduct factory inspections and compliance evaluations
Produce detailed technical reports and test summaries
Perform peer reviews of documentation and certification reports
Ensure projects are delivered on time, within scope, and to quality standards

What we’re looking for:

Degree (or equivalent) in Electrical or Electronic Engineering
Experience in electrical safety testing and CE marking compliance
Good understanding of IEC operational documents and certification processes (including CTF)
Knowledge of global market access requirements for electrical products
Strong understanding of electrical/electronic circuits
Experience working with laboratory quality procedures and testing environments
Excellent interpersonal and communication skills for client-facing work
Ability to work independently and as part of a team
Willingness to visit client sites and undertake occasional international travel
Full UK driving licence

Desirable experience:

Experience within a product testing or certification environment
Knowledge of regulatory and global certification procedures
Familiarity with standards such as IEC 62368, IEC (phone number removed), and IEC (phone number removed)
Experience conducting CIG023 inspections

Benefits include:

33+ days holiday, pension, life assurance, and comprehensive wellbeing support
Flexible benefits schemes including cycle to work and holiday purchase options
Employee assistance programme and occupational health support
Opportunities for career development within a global technical organisation

This is a fantastic opportunity for an Electrical Safety Engineer looking to progress into a senior role while working on complex compliance and certification projects.

Ref: #LI-FT1

Should you require any support or assistance, please contact your local Gi Group office.

Gi Group Holdings Recruitment Limited are proud founding members of Menopause in business, pledge members for Neurodiversity in business, Disability committed members, Silver status pledge members for the Armed Forces Covenant, and Bronze trail blazers for Racial Equality matters.

Gi Group Holdings Recruitment Limited group of companies includes Gi Recruitment Limited, Draefern Limited, Gi Group Recruitment Ltd, INTOO (UK) Limited, Marks Sattin (UK) Limited, TACK TMI UK Limited, Grafton Professional Staffing Limited, Encore Personnel Services, Gi Group Ireland Limited and Kelly Services (UK) Ltd. Gi Group Ireland Limited are acting as an Employment Agency in relation to this role.

We are committed to protecting the privacy of all our candidates and clients. If you choose to apply, your information will be processed in accordance with the Gi Group Privacy Statement. To view a copy and to help you understand how we collect, use and process your personal data please visit the Privacy page on our Gi Group website

Fire & Security Service Engineer (CCTV, Access Control, Fire & Intruder Alarms) – Blackburn – £40,000–£42,000 + Overtime

We are currently recruiting for an experienced Fire & Security Service Engineer to join a well-established and growing fire and security systems company covering Huddersfield and surrounding areas. Due to continued expansion and increasing customer demand, our client is looking to strengthen their engineering team with a skilled, multi-disciplined service engineer.

This is a full-time, permanent, field-based role offering a competitive basic salary, overtime, on-call earnings, a company vehicle, and ongoing training across fire and security systems.

Package & Benefits

*

Salary 40,000 – £42,000 per annum (negotiable depending on experience)

*

Overtime available

*

On-call rota with additional earnings

*

Company vehicle and fuel card

*

Travel time paid

*

Pension scheme

*

Annual leave entitlement

*

Ongoing training and development

*

Full-time, permanent position

*

Field-based role covering Blackburn and surrounding areas

Role & Responsibilities

*

Servicing, maintenance, fault-finding, and repair of IP CCTV, Access Control, Fire Alarm, and Intruder Alarm systems

*

Carrying out planned and reactive maintenance across commercial sites

*

Working with a wide range of manufacturers’ systems

*

Diagnosing faults and completing effective remedial works

*

Ensuring all work is completed to a high standard and in line with industry regulations

*

Maintaining clear and professional communication with customers

*

Completing service reports and documentation accurately and on time

*

Supporting other engineers and assisting the wider team when required

Skills & Experience Required

*

Full UK driving licence (essential)

*

Previous experience as a Fire & Security Service Engineer or Security Engineer

*

Ideally 3+ years’ experience within the fire and/or security industry (desirable, not essential)

*

Experience in one or more of the following: CCTV, Access Control, Fire Alarms, Intruder Alarms

*

Familiarity with a variety of manufacturers’ systems

*

Willingness to undertake additional training and upskilling

*

IPAF, CSCS/ECS, FIA, City & Guilds (desirable)

*

Positive attitude, strong work ethic, and self-motivation

Apply

If you are a Fire & Security Service Engineer looking for a secure, long-term role with strong earning potential and training opportunities in Blackburn, please submit your CV to be considered.

Keywords

Fire & Security Service Engineer, Fire and Security Engineer, CCTV Engineer, Access Control Engineer, Fire Alarm Engineer, Intruder Alarm Engineer, Fire & Security Maintenance, IP CCTV, Fire Systems Engineer, Security Systems Engineer, Blackburn Fire and Security Engineer, ECS Security Engineer, FIA Engineer, CSCS Fire Engineer

Telecoms Fibre Engineer

We are hiring for an award-winning company offering exceptional telecoms fibre engineer opportunities.

Start date of Telecoms Fibre Engineer:

• Immediate start available.

Pay of Telecoms Fibre engineer

• Annual salary with company package included.

-Company Pension Scheme – Yearly Bonus Scheme – Death in service – Annual Leave – Access to career developmental opportunities.

-Full equipment provided including company van & fuel card.

Job Description of Telecoms Fibre Engineer:

• Completing Fibre installations overhead and underground fibre.

• Blowing fibre, splicing, backfill and reinstatement

• Use and basic maintenance of a works tablet, fibre splicing machine, Power Meter, Fibre Identifier and Microscope.

• Respond professionally and effectively to all customer requests and enquiries

Key Requirements of Telecoms Engineer

• Full UK driver’s license with no more than 6 points on.

• Accreditations: SA001, SA002, NRSWA

• You will be Friendly, Customer focussed and desire to resolve any issues.

Telecoms fibre engineer physical requirements:

• The ability to lift objects regularly

• The ability to safely climb ladders

• The ability to bend and stretch with comfort

• The ability to wear personal protective gear correctly most of the day

Salary circa £42-48,000 (DOE)
A well-established production factory, based in Chichester is looking to recruit a skilled Plant Maintenance Engineer, with solid electrical understanding, to support ongoing reliability through effective servicing, repairs and planned preventative maintenance of their production machinery.
Working Hours:
Monday to Friday – 9 hours per day
• Late morning starts Monday–Thursday
• 7:00am start on Fridays
Key Responsibilities:
Service, repair and planned preventative maintenance (PPM) on production machinery
Electrical and mechanical fault finding and repairs
Maintenance work involving hydraulics and pneumatics
Supporting continuous improvement and minimising downtimeSkills & Experience Required:

Strong multi-skilled maintenance background (electrical & mechanical)
Experience within manufacturing environments advantageous
Knowledge of hydraulics and pneumatics
Electrical three phase experience in a production environment
Ability to work independently and respond proactively to maintenance issuesWhat’s On Offer:

Salary around £42-48,000 depending on experience
Stable Monday–Friday role with structured hours
Opportunity to join a well-established manufacturing businessIf you’re a proactive maintenance engineer looking for your next challenge in a busy production environment, we’d love to hear from you

Introduction

Saab UK is part of Scandinavia’s largest defence company, bringing together the best of Swedish and British innovation. Saab offers world-leading solutions and services in defence, aviation, space, and civil security to keep people and society safe. Our UK presence has been growing at pace, meaning we can offer a wide range of opportunities for personal fulfilment and career growth. We currently employ over 600 people across eight sites in the UK, and our specialisations include software engineering, underwater robotics, radars, AI, and armed forces training.

What you will be part of:

Explore a wealth of possibilities. Take on challenges, create smart inventions, and grow beyond. This is a place for curious minds, brave pioneers, and everyone in between. Together, we achieve the extraordinary, each bringing our unique perspectives. Your part matters.

Saab is a leading defence and security company with an enduring mission, to help nations keep their people and society safe. Empowered by its 26,000 talented people, Saab constantly pushes the boundaries of technology to create a safer and more sustainable world.

Saab designs, manufactures and maintains advanced systems in aeronautics, weapons, command and control, sensors and underwater systems. Saab is headquartered in Sweden. It has major operations all over the world and is part of the domestic defence capability of several nations. Read more about us .

The Role:

This role will be a part of our Saab Seaeye business in Fareham.

In this role you will take responsibility for the full-lifecycle design and development of bespoke power conversion and transmission solutions in line with the company’s business needs through innovation, creativity and professionalism. As Lead Engineer you will act as Technical Authority for concurrent power projects: from in-house designs to outsourced specification and management.

Key Responsibilities:

The role seeks an engineer with excellent knowledge of power architectures, transmission, conversion and distribution, whilst having an appreciation for the real-world subtleties involved in creating robust and reliable power systems. You may be working on anything from large-scale power conversion products, efficient cabled transmission designs all the way through to motor drives and low voltage converters. Our voltages range from 24V to 5000V with powers from 500W to 250kW.

You will be responsible for the successful design, implementation and delivery into our products. This may include technically leading small multi-disciplinary teams and therefore the candidate must show an aptitude for directing and coordinating project activities and have strong communication/interpersonal skills. A product-focussed mindset is essential: taking a view across the different engineering disciplines to deliver the most appropriate solution. Our products provide unique challenges in designing non-conventional solutions which can meet size, weight and efficiency demands.

Qualifications and Skills:

Essential:

Significant Experience in Power Electronics
Full-lifecycle experience: from concept to tested solution
Self-starter: taking the lead and having a proactive mindset
Excellent theoretical knowledge backed up by proven hands-on experience
Proven knowledge of power transmission: AC and DC, applied to multi-km cabled solutions
Proven Knowledge of DC converter topologies: Buck/Boost/Flyback/LLC/Full-Bridge
Proven Knowledge of AC converter techniques: single phase/multiphase, power factor correction
Experience of power converter product design AC-DC, DC-DC and DC-AC inverters
Experience working with power switching devices: MOSFET, IGBT, SiCFET, GaNFET and associated drive circuitry
Experience working with voltages up to 5kV and multi-kW powers
Experience in designing or specifying custom transformer and magnetic components
Experience using modelling and simulation packages
Experience in both digital and analogue design concepts
Experience of filter design and implementation
Experience designing/specifying control systems for power conversion
Knowledge of thermal management techniques
Knowledge of design-for-compliance
Experience developing requirements specifications and test procedures
Experience of System level integration and testing

Desirable:

High Voltage Experience up to 5kV
Thermal modelling experience
Motor design principles and control techniques
Embedded-C programming

By submitting an application to Saab UK you consent to undertaking workforce screening activities that may include but are not limited to: Baseline Personnel Security checks, National Security Vetting, reference checks, verification of working rights and in all circumstances preferred candidates will be placed through a security interview

Location: Fareham
Working Hours: Minimum for 40-hour working week.
Salary: £50,000 Per Annum

We are currently looking to recruit an Electrical Service Engineer to join our client, a well‑established engineering business specialising in pumping solutions.
The company is known for its high‑quality equipment, strong customer relationships, and commitment to safety, training, and professional development.

The Role

As an Electrical Service Engineer, you will play a key role in maintaining, repairing, and servicing a wide range of electrical and diesel pump systems. Working both in the depot and on customer sites, you’ll carry out diagnostics, troubleshooting, and electrical work to the highest standards while supporting the wider engineering team.

Key Responsibilities

* Diagnose, troubleshoot, maintain, repair, and overhaul pump fleet and associated equipment.

* Program PLC controls and complete final electrical connections on site installations.

* Focus primarily on electrical pump systems, with some involvement in diesel units.

* Work both in the depot and on external customer sites.

* Follow all Health & Safety requirements, including correct use of PPE.

* Complete all required paperwork, reports, timesheets, expenses, and QHSE documentation.

* Adhere to company quality, health, safety, and environmental procedures.

* Support and mentor new engineers and apprentices.

* Maintain high standards of workmanship and customer service.

* Participate in an out‑of‑hours on‑call rota for emergency breakdowns.

* Undertake training relevant to the role and personal development.

* Ensure personal documentation (e.g., driving licence, medicals) is kept up to date.

* Maintain and calibrate tools and equipment in line with company and manufacturer guidelines.

* Report PPE requirements and ensure equipment is properly cared for.

* Carry out additional tasks as required to support the department and wider business.

Experience & Skills Required

* Completed a recognised electrical or mechanical apprenticeship.

* Minimum of two years’ experience working with similar products in a service environment.

* Competent with diagnostic tools and relevant engineering equipment.

* Able to work independently and as part of a team.

* Strong verbal and written communication skills.

* Confident liaising with colleagues, management, suppliers, OEMs, and customers.

Qualifications

* 18th Edition qualification (essential).

* Full UK driving licence (essential).

* CSCS card preferred but not essential.

What the Company Offers

* £50K Salary

* Enhanced overtime rates.

* 24 days holiday plus Bank Holidays.

* Ongoing training and development support.

* Use of a company vehicle.

* Death‑in‑service benefit

JOB - Electrical Design Engineer

LOCATION – Portsmouth

TERM – Permanent

SALARY - £40,000 - £45,000 (Dependant on experience)

The Electrical Design Engineer will be responsible for the design and development of electrical systems used within the company’s manufactured equipment. This role involves working closely with multidisciplinary teams including mechanical design, controls, and production to deliver reliable and compliant electrical designs.

Key Responsibilities

Design electrical schematics, wiring diagrams, and control panel layouts
Develop electrical systems for bespoke and standard manufacturing equipment
Produce technical documentation including bills of materials and specifications
Ensure designs comply with relevant electrical standards and regulations
Support the build, test, and commissioning of equipment when required
Work collaboratively with internal teams to resolve design and production issues
Contribute to continuous improvement of design processes and standards

Requirements

Degree, HND, or equivalent qualification in Electrical Engineering or a related discipline
Experience in electrical design within a manufacturing or machinery environment
Proficiency with electrical design software such as AutoCAD Electrical, EPLAN, or similar
Knowledge of relevant standards and regulations
Strong problem-solving skills and attention to detail
Ability to work both independently and as part of a team
If you are interested in this position, please apply with an up to date CV as soon as possible, along with your availability and your salary expectation

Altera Recruitment Group is partnered with a high-growth engineering and manufacturing business undergoing significant expansion. The company operates at the cutting edge of advanced production technology, designing and building complex, high-performance manufacturing equipment for demanding industrial environments. This is a hands-on engineering role offering exposure to new production lines, novel machinery, and end-to-end control systems delivery within a modern R&D and manufacturing setting.

As the Electrical Engineer, you’ll be part of a specialist engineering team responsible for the design, development and commissioning of electrical and control systems for complex production equipment. The role blends technical design work with on-the-floor involvement during build, installation and commissioning phases.

The responsibilities of the Electrical Engineer include:

* Specify, design and support the delivery of electrical and control systems for advanced manufacturing equipment and new production lines.

* Work with PLC-based control systems, motion control, drives, safety systems and machine monitoring solutions.

* Support commissioning, fault-finding and optimisation activities across both new and existing manufacturing assets.

* Collaborate closely with mechanical engineers, production teams, suppliers and contractors to deliver engineering work packages.

* Produce clear technical documentation including specifications, drawings, test plans and handover materials.

Requirements:

* Degree-qualified in Electrical Engineering or equivalent practical experience within an industrial or manufacturing environment.

* Proven experience working with automated control systems, electrical power distribution and circuit fault-finding.

* Comfortable working across both design/specification and hands-on implementation on the shop floor.

* Working knowledge of PLC-based systems and motion control.

* Strong communication skills and the ability to manage multiple priorities in a fast-paced project environment.

What this is offering:

* A highly competitive salary, depending on experience

* Company bonus scheme up to 10%

* Pension up to 10%

* Other Industry-leading benefits

This is an opportunity to join an engineering organisation investing heavily in technology, innovation and manufacturing capability. You’ll work on technically challenging equipment, gain exposure to full lifecycle projects and develop your career within a business that values engineering-led problem solving

Electronics Design Engineers
Location: Broad Oak, Portsmouth, 4 days on site per week
Duration: 6 months
Rate: £60.63 per hour PAYE or up to £81.90 per hour Umbrella
SC Clearance required, BPSS to start

4 Roles
• Electronic Engineer: Supporting the electronic Safety Depth Sensor PCB/PEC (SDSP) within the Electronics Sub System for Torpedo Development.
• Electronic Engineer: Providing sonar design and analogue engineering expertise for Recovery and Instrumentation (R&I) Sub System Design within Torpedo Development.
• Electronic Engineer: Supporting design proving and test activities for the Recovery and Instrumentation (R&I) Sub System within Torpedo Development.
• Electronic Engineer: Working on Torpedo Afterbody Sub System Design, supporting Return to Manufacture activities for propulsion, control, and navigation elements.

This is a technical role relating to the Electronic aspects of hardware design & test.
The Role Holder will :-
• Develop and/or support electronic design solutions for both new products and technology insertions into legacy products.
• Produce and/or support detailed designs from concept to completion and addressing a range of engineering challenges.
• Participating in all aspects of board and unit level design and test activities, including interfaces with higher level assemblies.

Typical duties include (but are not limited to):
• Detailed electronic circuit design including component selection, evaluation, simulation, schematic capture, and liaising with PCB design teams.
• Specification of bespoke procured hardware.
• Design verification using a combination of simulation, analysis, and test techniques, including support to EMC test houses and customer installations.
• Generate design documentation and technical reports.
• Interfacing with related disciplines.
• Assist the development of higher level system designs.
• Assist the development of technical requirement specifications
• Support system integration activities.
• Work with embedded software and PLD engineers as necessary
• Contribute to progress, peer, and design reviews.

Key Skillset
Knowledge:
• Generating component level electronic designs for introduction into volume production.
• Digital design including processor interfacing, memory devices, PLD interfacing, UARTs, SPI, I2C, Ethernet etc.
• ADC/DAC devices and techniques
• Analogue design including op-amps, transistor-level design, control loops and low noise techniques.
• High power techniques.
• Design proving, integration, and defect resolution.
• Gathering of evidence to support acceptance, fitness for purpose, legislative requirements, and safety.
Skills:
• Previous Knowledge of operating in a defence or high safety integrity environment.
• Knowledge of low-noise analogue techniques
• Knowledge of high power techniques (kW level)
• Knowledge of FPGA/CPLD development